The full name of the FCC is the Federal Communications Commission, and the Chinese name is the US Federal Communications Commission. Established by COMMUNICATIONACT in 1934, it is an independent agency of the United States Government and is directly accountable to Congress. The FCC coordinates domestic and international communications by controlling radio, television, telecommunications, satellite and cable. Involving more than 50 U.S. states, Columbia, and the U.S. territories To ensure the safety of radio and wire communications products related to life and property, the FCC's Office of Engineering and Technology is responsible for the technical support of the committee, and is also responsible for equipment approval Business. Many radio application products, communication products and digital products need to apply for registration in the American Wireless Alliance-FCC-ID. If you want to enter the US market, you can check company and product information in the Wireless Alliance through the ID number.
What are the requirements for FCC certification of wireless charging products?
Regarding FCC certification, depending on the operating configuration, the part of regulations that wireless power transmission equipment may need to comply with is FCC PART 15, FCC PART 18, or both. Specific requirements are as follows:
1. When the device is certified according to FCC PART 15, the device cannot transmit between 90-110kHz because it is limited to §15.205 in FCC PART 15C;
2. When the device is certified according to FCC PART 18, the rules of PART 18 allow the device to operate in the engineering and medical band and generate and use RF energy for local work applications. However, for consumer devices, it must be used at ultra close range, and this RF energy cannot be used for communication purposes, that is, only charging mode;
3. When the priority of the device is to charge the device and transmit any other data such as extended system data, images or music, for such a design, the requirements of PART 15 and 18 must be met when the device is certified.
Wireless charging products may have two different working modes: charging mode and communication mode. In this case, it is possible to use FCC Part 18 for the charging mode and FCC Part 15 for the communication mode, but the premise is that the two modes of charging and communication are independent of each other. If the charging mode meets all relevant provisions of Part 15, the FCC allows the charging mode to replace Part 18 with Part 15.
Which products need FCC ID?
1. Transmitting frequency: 125KHz, 13.56MHz
Typical products: door card reader, bus card reader, wireless charger;
2. Transmitting frequency: 27MHz, 49MHz
Typical products: remote control toys, wireless mouse;
3． Transmission frequency: 315MHz, 433MHz (intermittent, periodic products, remote control toys are prohibited)
Typical products: remote control switch, wireless doorbell, anti-theft device;
4． Transmitting frequency: 88-108MHz
Typical products: car FM transmitter;
5. Transmitting frequency: 902-928MHz, 2400-2483.5MHz, 5725-5850MHz
Typical products: remote control toys, wireless mouse, Bluetooth speaker, WIFI drone, smart home products;
Information required for FCC-ID certification:
1. Fixed frequency method (fixed frequency program, fixed frequency operation) (that is, the wireless transmission can be continuously transmitted on any channel and can be selected)
2. Frequency range and number of channels, modulation method and channel mode (such as WIFI, IEE802.11B / G or IEE802.11B / G / NHT20 or 80211B / G / NHT20 / NHT40, modulation method is FHSS, etc.)
3. Instructions (product instructions)
4. Circuit diagram (circuit schematic diagram of the entire product, including circuit boards and modules)
5.Block diagram (that is, connect one part as a module according to the circuit diagram, such as power module, WIFI module, IC module, etc., and the frequency of the crystal needs to be reflected)
6.PCBLAYOUT picture (layout picture of PCB board, front and back)
7. Job description (operation description) (that is, describing how the product's wireless works, and what modulation to transmission can be based on the block diagram)
8. Antenna information (that is, the information of the wireless transmitting antenna, if there is no way to provide it, you need to provide the antenna gain, such as antenna max gain: 2dBi, telec certification must provide)
9.LABEL diagram (nameplate) and placed position
10.BOM (Bill of Materials)
11. FCC application form: the application company name, address, contact information, product name and model, and use information are required to be accurate;
FCC-ID certification cycle: 3-4 weeks (depending on product features).
FCC-ID certification fee: directly contact the sales elite of Shenzhen Zhongjianlian Testing Technology Co., Ltd.
If you need to know the FCC-ID certification fee, FCC-ID certification process, FCC-ID certification information, FCC-ID certification time, FCC-ID certification laboratory, FCC-ID certification agency can directly contact Shenzhen Zhongjianlian Testing Technology Co., Ltd. the company!